BDS 4-Inch Lift Kit | FOX 2.0 Shocks | Leaf Springs + 3.5-Inch Axle Block | Ram 2500 Power Wagon 4WD 2008 | SKU: 1767FS

The BDS 1767FS is a 4-inch lift kit with FOX 2.0 Performance Series shocks for the 2008 Ram 2500 Power Wagon 4WD — 2008 only. Front lift is delivered via 2008-specific Power Wagon coil springs and geometry-correct radius arm brackets engineered for the Dana 60 front axle. Rear lift is matched via replacement leaf springs and 3.5-inch axle blocks. The factory electronic sway bar disconnect system is preserved at lifted height.

BDS engineers a separate kit for each Power Wagon generation because the suspension specifications differ between years. The 2005–2007 Power Wagon requires 1764FS. The 2009–2013 Power Wagon requires 1770FS. The components in this kit are specific to the 2008 model year and are not interchangeable with adjacent year kits or with standard Ram 2500 lift kits.

Confirm your model year is exactly 2008 before ordering. Text (469) 407-7538 if you need confirmation before purchasing.

Component Specifications

What Is and Is NOT Included

Critical Compatibility

This kit is Power Wagon-specific and covers 2008 only. One year. No exceptions.

Not sure which Power Wagon generation you have? Text (469) 407-7538 before ordering.

Power Wagon Generation Reference — BDS Lift Kit By Year

Tire Clearance

At 4 inches of lift on the 2008 Power Wagon platform, typical fitment runs 35–37-inch tires depending on wheel offset and backspacing. Confirm maximum tire diameter and wheel specifications with your wheel and tire supplier before ordering.

Installation Notes

Professional installation is required — Dana 60 and sway bar disconnect familiarity mandatory. The 2008 Power Wagon lift requires a qualified suspension shop familiar with Dana 60 front axle geometry and the Power Wagon's factory electronic sway bar disconnect system. Do not attempt DIY installation.

Full front-end alignment is mandatory after installation. Do not drive on public roads before alignment is completed.

Electronic sway bar disconnect verification is required after installation. The 2008 Power Wagon uses a factory electronic sway bar disconnect system. Verify that the system functions correctly at lifted height after installation before road or trail use.

Rear axle block installation. 3.5-inch axle blocks must be installed per BDS specifications. Confirm U-bolt torque specs and axle centering after installation — improperly centered axle blocks cause driveline vibration and premature U-joint wear.

Torque all fasteners to BDS specification. Torque specs are included in the BDS installation instructions. Do not estimate torque values.

FOX shock break-in period. Allow FOX 2.0 shocks to complete the manufacturer-recommended break-in period before aggressive off-road use.

Text (469) 407-7538 to confirm your Power Wagon model year before ordering.

The Obsidian Take

The BDS 1767FS is the correct kit for the 2008 Ram 2500 Power Wagon owner who wants 4 inches of front and matched rear lift with FOX 2.0 damping — engineered specifically for the Dana 60 front axle geometry and the factory electronic sway bar disconnect system of the second-generation Power Wagon. The year-specific coil springs, Dana 60-specific radius arm brackets, and matched rear leaf spring package are purpose-built for 2008. They are not interchangeable with the 2005–2007 or 2009–2013 Power Wagon kits, and they are not interchangeable with standard Ram 2500 lift components.

If your Power Wagon is a 2005–2007, order 1764FS. If it is a 2009–2013, order 1770FS. If it is a 2014 or newer, text (469) 407-7538 to confirm the correct platform before ordering. If your Ram 2500 does not have the Power Wagon package, this kit's geometry-specific components are not the correct fit for the standard suspension architecture.

2008, Power Wagon, Dana 60, electronic sway bar disconnect — the 1767FS is the complete, year-correct lift solution.

Common Questions

Why is the 2008 Power Wagon a separate kit from the 2005–2007 and 2009–2013?
BDS engineers year-specific Power Wagon kits because the suspension specifications differ across Power Wagon generations. The 2008 Power Wagon has different coil spring requirements and geometry correction needs from the 2005–2007 and 2009–2013 generations — using the wrong year kit installs incorrect geometry correction for your axle.

Will this kit work with the factory electronic sway bar disconnect?
Yes. This kit preserves the factory electronic sway bar disconnect system at lifted height. Verify that the sway bar disconnect functions correctly after installation before road or trail use.

Why can't I use a standard Ram 2500 lift kit on my Power Wagon?
The Power Wagon uses a Dana 60 front axle with different suspension geometry than the standard Ram 2500. The radius arm brackets and coil springs in this kit are engineered for Dana 60 geometry — standard Ram 2500 lift kits are not designed for the Dana 60 mounting points and geometry correction requirements.

Does this kit lift the rear of the truck?
Yes. Front lift is via Power Wagon-specific coil springs and radius arm brackets. Rear lift is matched via replacement leaf springs and 3.5-inch axle blocks — both included in this kit.

Is this a DIY install?
No. The Power Wagon-specific lift requires a qualified suspension shop familiar with Dana 60 front axle geometry and the factory electronic sway bar disconnect system. Professional installation is required.

What tire size fits at 4-inch lift?
Typical fitment on the 2008 Power Wagon at 4-inch lift runs 35–37-inch tires depending on wheel offset and backspacing. Confirm maximum tire diameter and wheel specs with your wheel and tire supplier before ordering.

What warranty does this kit carry?
BDS suspension components carry the BDS No-Fine-Print Warranty. FOX 2.0 shocks carry a FOX 1-year limited warranty.

Verified Fitment