{"product_id":"bds-5-5-inch-lift-kit-bds1619fs-ram-3500-2013-2018-gas","title":"BDS 5.5-Inch Lift Kit — Ram 3500  SKU: BDS1619FS | Ram 3500 2013–2018 | 4WD | Gas | 5.5\" Front \/ 4.5\" Rear | FOX 2.0 Performance Series | Leaf Springs Rear","description":"\u003cp dir=\"ltr\"\u003eA complete 5.5-inch suspension lift kit engineered for the 2013–2018 Ram 3500 gas 4WD. The front lift uses gas-specific progressive rate Pro-Ride coil springs with radius arm drop brackets to correct suspension geometry while retaining the factory radius arms. A forged drop pitman arm and track bar bracket correct steering geometry. A transfer case indexing ring and high-clearance transmission crossmember address driveline geometry at this lift height. The rear uses progressive rate multi-leaf springs for a 4.5-inch rear lift with extended U-bolts. FOX 2.0 Performance Series shocks front and rear. Supports up to 37-inch tires.\u003c\/p\u003e\n\u003chr\u003e\n\u003cblockquote dir=\"ltr\"\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eBefore ordering:\u003c\/strong\u003e Gas 4WD only. This kit is rated Difficult — confirm installer has step drill bit, drill\/bit set, and welding equipment before scheduling. \u003cstrong\u003eExhaust modification note: 6.4L gas models require exhaust modification to clear the front driveshaft. 5.7L gas models may require it as well.\u003c\/strong\u003e The vehicle can be driven without the front driveshaft to an exhaust shop. If equipped with a 2-piece rear driveshaft (carrier bearing), a carrier bearing drop is required. Some vehicles may also require rear driveshaft spacer kit 122007 to maintain adequate rear driveshaft engagement. DRW models: inner wheel clearance to the upper U-bolt plate applies on 5.5–6 inch kits.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003cblockquote dir=\"ltr\"\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eRequired separately (conditional):\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eCarrier bearing drop — required if equipped with 2-piece rear driveshaft; confirm PN with BDS\u003c\/li\u003e\n\u003cli\u003eRear driveshaft spacer kit 122007 — may be required on some vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch4 dir=\"ltr\"\u003eVerified Fitment\u003c\/h4\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eYear\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eMake\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eModel\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eTrims\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eDrive\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eFuel\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2013\u003c\/td\u003e\n\u003ctd\u003eRam\u003c\/td\u003e\n\u003ctd\u003e3500\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e4WD\u003c\/td\u003e\n\u003ctd\u003eGas\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2014\u003c\/td\u003e\n\u003ctd\u003eRam\u003c\/td\u003e\n\u003ctd\u003e3500\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e4WD\u003c\/td\u003e\n\u003ctd\u003eGas\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2015\u003c\/td\u003e\n\u003ctd\u003eRam\u003c\/td\u003e\n\u003ctd\u003e3500\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e4WD\u003c\/td\u003e\n\u003ctd\u003eGas\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2016\u003c\/td\u003e\n\u003ctd\u003eRam\u003c\/td\u003e\n\u003ctd\u003e3500\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e4WD\u003c\/td\u003e\n\u003ctd\u003eGas\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2017\u003c\/td\u003e\n\u003ctd\u003eRam\u003c\/td\u003e\n\u003ctd\u003e3500\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e4WD\u003c\/td\u003e\n\u003ctd\u003eGas\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2018\u003c\/td\u003e\n\u003ctd\u003eRam\u003c\/td\u003e\n\u003ctd\u003e3500\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e4WD\u003c\/td\u003e\n\u003ctd\u003eGas\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003ch4 dir=\"ltr\"\u003eComponent Specifications\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eLift Configuration (this SKU):\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eAttribute\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eBDS Suspension\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSKU\u003c\/td\u003e\n\u003ctd\u003eBDS1619FS\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFront lift height\u003c\/td\u003e\n\u003ctd\u003e5.5 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFront lift method\u003c\/td\u003e\n\u003ctd\u003eCoil spring with radius arm drop brackets\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRear lift height\u003c\/td\u003e\n\u003ctd\u003e4.5 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRear lift method\u003c\/td\u003e\n\u003ctd\u003eLeaf spring\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShock option (this build)\u003c\/td\u003e\n\u003ctd\u003eFOX 2.0 Performance Series\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum tire clearance\u003c\/td\u003e\n\u003ctd\u003eUp to 37 inches (trimming may be required)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEstimated install time\u003c\/td\u003e\n\u003ctd\u003e7–9 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDifficulty level\u003c\/td\u003e\n\u003ctd\u003eDifficult\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpecialty tools required\u003c\/td\u003e\n\u003ctd\u003eStep drill bit, drill\/bit set, pitman arm puller, welding equipment\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003ePro-Ride Coil Springs — Front:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eAttribute\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eType\u003c\/td\u003e\n\u003ctd\u003eFull-length, progressive rate\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eApplication\u003c\/td\u003e\n\u003ctd\u003eGas-specific\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLift provided\u003c\/td\u003e\n\u003ctd\u003e5.5 inches (front)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eRadius Arm Drop Brackets:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eAttribute\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eType\u003c\/td\u003e\n\u003ctd\u003eDrop brackets — factory radius arms retained\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFunction\u003c\/td\u003e\n\u003ctd\u003eCorrects suspension geometry at lifted height\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eRear Lift — Leaf Springs:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eAttribute\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eType\u003c\/td\u003e\n\u003ctd\u003eMulti-leaf, progressive rate\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLift provided\u003c\/td\u003e\n\u003ctd\u003e4.5 inches (rear)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAxle wrap\u003c\/td\u003e\n\u003ctd\u003eReduced vs. block configuration\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePayload rating\u003c\/td\u003e\n\u003ctd\u003eFactory payload weight ratings maintained\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eFOX 2.0 Performance Series Shocks (front and rear):\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eAttribute\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBody diameter\u003c\/td\u003e\n\u003ctd\u003e2 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBody material\u003c\/td\u003e\n\u003ctd\u003eImpact extruded aluminum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDesign\u003c\/td\u003e\n\u003ctd\u003eInternal floating piston (IFP) monotube\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMounting ends\u003c\/td\u003e\n\u003ctd\u003eCNC machined 6061-T6 aluminum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShaft\u003c\/td\u003e\n\u003ctd\u003e5\/8-inch hard chrome plated heat-treated alloy steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePiston\u003c\/td\u003e\n\u003ctd\u003eRace-developed high-flow design\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eValving\u003c\/td\u003e\n\u003ctd\u003eApplication-specific\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFinish\u003c\/td\u003e\n\u003ctd\u003eClear anodized\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eRecommended Tire and Wheel Configurations (trimming may be required):\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eTire Size\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eWheel\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eBackspace\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e35 x 12.50\u003c\/td\u003e\n\u003ctd\u003e17 x 9\u003c\/td\u003e\n\u003ctd\u003e4.5 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e35 x 12.50\u003c\/td\u003e\n\u003ctd\u003e18 x 9\u003c\/td\u003e\n\u003ctd\u003e4.5 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e37 x 13.50\u003c\/td\u003e\n\u003ctd\u003e17 x 9\u003c\/td\u003e\n\u003ctd\u003e5.625 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003ch4 dir=\"ltr\"\u003eWhat Is and Is NOT Included\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eIncluded — Front:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eGas-specific progressive rate Pro-Ride coil springs (pair)\u003c\/li\u003e\n\u003cli\u003eRadius arm drop brackets\u003c\/li\u003e\n\u003cli\u003eForged drop pitman arm\u003c\/li\u003e\n\u003cli\u003eTrack bar relocation bracket\u003c\/li\u003e\n\u003cli\u003eSway bar correction hardware\u003c\/li\u003e\n\u003cli\u003eBump stops\u003c\/li\u003e\n\u003cli\u003eBrake line brackets\u003c\/li\u003e\n\u003cli\u003eTransfer case indexing ring\u003c\/li\u003e\n\u003cli\u003eHigh-clearance transmission crossmember\u003c\/li\u003e\n\u003cli\u003eFOX 2.0 Performance Series front shocks\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eIncluded — Rear:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eMulti-leaf progressive rate rear springs (4.5-inch lift)\u003c\/li\u003e\n\u003cli\u003eExtended U-bolts\u003c\/li\u003e\n\u003cli\u003eFOX 2.0 Performance Series rear shocks\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eNot included (conditional — may be required):\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eCarrier bearing drop — required if equipped with 2-piece rear driveshaft; confirm PN with BDS\u003c\/li\u003e\n\u003cli\u003eRear driveshaft spacer kit 122007 — may be required on some vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eCritical Compatibility\u003c\/h4\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003e\n\u003cstrong\u003eGas engine only:\u003c\/strong\u003e Gas-specific Pro-Ride coil springs are included. Diesel Ram 3500 is not supported.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRadius arm drop brackets — factory arms retained:\u003c\/strong\u003e This kit uses drop brackets to correct suspension geometry at the lifted height. The factory radius arms remain in place. This is distinct from kits that replace the factory arms with HD tubular radius arms.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExhaust modification — engine-specific:\u003c\/strong\u003e 6.4L gas models require exhaust modification to clear the front driveshaft. 5.7L gas models may require it. Confirm your engine and have a plan before scheduling installation. The vehicle can be driven without the front driveshaft to an exhaust shop.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e2-piece rear driveshaft:\u003c\/strong\u003e A carrier bearing drop is required if your truck has a 2-piece rear driveshaft. Confirm your driveshaft configuration and the applicable PN with BDS before ordering.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRear driveshaft spacer:\u003c\/strong\u003e Some vehicles may require spacer kit 122007 to maintain adequate rear driveshaft engagement.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDRW models:\u003c\/strong\u003e Inner wheel clearance to the upper U-bolt plate is a consideration on 5.5–6 inch kits for dual rear wheel trucks.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDifficulty rated Difficult:\u003c\/strong\u003e Step drill bit, drill\/bit set, pitman arm puller, and welding equipment are all required. Confirm installer is equipped before scheduling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eADAS recalibration:\u003c\/strong\u003e Required after installation. All recalibration costs are the owner's responsibility.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eInstallation Notes\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003eProfessional installation is strongly recommended. This kit is rated Difficult with an estimated installation time of 7–9 hours. Specialty tools required: step drill bit, drill\/bit set, pitman arm puller, and welding equipment.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eExhaust modification:\u003c\/strong\u003e 6.4L gas models require this before front driveshaft reinstallation. 5.7L models may require it. The Ram 3500 can be driven without the front driveshaft to an exhaust shop.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eVerify before beginning:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eConfirm gas engine and plan for exhaust modification if applicable\u003c\/li\u003e\n\u003cli\u003eRear driveshaft type — 2-piece requires carrier bearing drop\u003c\/li\u003e\n\u003cli\u003eConfirm with BDS whether driveshaft spacer kit 122007 is needed\u003c\/li\u003e\n\u003cli\u003eDRW inner wheel clearance verified if applicable\u003c\/li\u003e\n\u003cli\u003eAll specialty tools confirmed on site\u003c\/li\u003e\n\u003cli\u003eADAS recalibration appointment scheduled\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003eProfessional alignment is required after installation. Refer to the current BDS Suspension installation instructions for SKU BDS1619FS for complete procedures, torque specifications, and component-specific instructions.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eThe Obsidian Take\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003eThe BDS1619FS takes a different approach than every other Ram 3500 kit in this catalog — it uses radius arm drop brackets to correct suspension geometry at 5.5 inches rather than replacing the factory arms with HD tubular units. The factory radius arms stay in place; the drop brackets reposition them at the correct angle for the lifted height. Gas-specific Pro-Ride coil springs, leaf spring rear at 4.5 inches for axle wrap control and payload retention, and FOX 2.0 shocks complete the build. The exhaust modification requirement is engine-dependent — 6.4L owners should schedule that shop visit before installation day; 5.7L owners should confirm at pre-install. Difficult rating with welding equipment and a step drill bit on the required tool list — confirm the installer is equipped for all four specialty tools before booking.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eThis Product Is For You If\u003c\/h4\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eYou own a 2013–2018 Ram 3500 gas 4WD.\u003c\/li\u003e\n\u003cli\u003eYou want 5.5 inches of front lift and 4.5 inches of rear lift via leaf springs for axle wrap control and maintained payload ratings.\u003c\/li\u003e\n\u003cli\u003eYou want FOX 2.0 Performance Series shocks with application-specific valving.\u003c\/li\u003e\n\u003cli\u003eYou want up to 37-inch tire clearance.\u003c\/li\u003e\n\u003cli\u003eYou are prepared to address the exhaust modification requirement for your engine type.\u003c\/li\u003e\n\u003cli\u003eYour installer has step drill bit, drill\/bit set, pitman arm puller, and welding equipment.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eThis Product Is Not For You If\u003c\/h4\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eYour Ram 3500 has a diesel engine.\u003c\/li\u003e\n\u003cli\u003eYour Ram 3500 is 2WD.\u003c\/li\u003e\n\u003cli\u003eYou are not prepared to address exhaust modification if required for your engine.\u003c\/li\u003e\n\u003cli\u003eYour installer does not have all required specialty tools.\u003c\/li\u003e\n\u003cli\u003eYou want the block rear option — see the block kit variant.\u003c\/li\u003e\n\u003cli\u003eYou want NX2 Nitro Series shocks — see the NX2 variant.\u003c\/li\u003e\n\u003cli\u003eYou want FOX 2.5 Performance Elite Series shocks — see the FOX 2.5 variant.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eProduct Family Reference\u003c\/h4\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eSKU\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eFront Method\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eRear Option\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eLift\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eShock\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eNotes\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBDS1619FS (this product)\u003c\/td\u003e\n\u003ctd\u003eRadius arm drop brackets\u003c\/td\u003e\n\u003ctd\u003eLeaf Springs\u003c\/td\u003e\n\u003ctd\u003e5.5\" \/ 4.5\"\u003c\/td\u003e\n\u003ctd\u003eFOX 2.0\u003c\/td\u003e\n\u003ctd\u003eGas Ram 3500 2013–2018\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBlock kit variant\u003c\/td\u003e\n\u003ctd\u003eRadius arm drop brackets\u003c\/td\u003e\n\u003ctd\u003eBlock\u003c\/td\u003e\n\u003ctd\u003e5.5\" \/ varies\u003c\/td\u003e\n\u003ctd\u003eVarious\u003c\/td\u003e\n\u003ctd\u003eGas Ram 3500 2013–2018\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNX2 variant\u003c\/td\u003e\n\u003ctd\u003eRadius arm drop brackets\u003c\/td\u003e\n\u003ctd\u003eLeaf Springs\u003c\/td\u003e\n\u003ctd\u003e5.5\" \/ 4.5\"\u003c\/td\u003e\n\u003ctd\u003eNX2 Nitro\u003c\/td\u003e\n\u003ctd\u003eGas Ram 3500 2013–2018\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFOX 2.5 variant\u003c\/td\u003e\n\u003ctd\u003eRadius arm drop brackets\u003c\/td\u003e\n\u003ctd\u003eLeaf Springs\u003c\/td\u003e\n\u003ctd\u003e5.5\" \/ 4.5\"\u003c\/td\u003e\n\u003ctd\u003eFOX 2.5 Elite\u003c\/td\u003e\n\u003ctd\u003eGas Ram 3500 2013–2018\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003ch4 dir=\"ltr\"\u003eCommon Questions\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eDoes this kit fit the diesel Ram 3500?\u003c\/strong\u003e\u003cbr\u003eNo. Gas-specific Pro-Ride coil springs are included. Diesel is not supported.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhat are radius arm drop brackets — and how are they different from replacement radius arms?\u003c\/strong\u003e\u003cbr\u003eThis kit uses drop brackets that reposition the factory radius arms at the correct angle for the lifted height. The factory arms remain in place. Kits that replace the factory arms with HD tubular units are a different design approach.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eIs exhaust modification required?\u003c\/strong\u003e\u003cbr\u003eIt depends on your engine. 6.4L gas models require it. 5.7L gas models may require it. Confirm with your installer before scheduling. The truck can be driven without the front driveshaft to an exhaust shop.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eDo I need the carrier bearing drop?\u003c\/strong\u003e\u003cbr\u003eOnly if your Ram 3500 has a 2-piece rear driveshaft. Confirm your driveshaft configuration and the applicable PN with BDS before ordering.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhat about the rear driveshaft spacer kit?\u003c\/strong\u003e\u003cbr\u003eSome vehicles require spacer kit 122007 to maintain adequate rear driveshaft engagement. Confirm with BDS or your installer whether your specific build requires it.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eMy truck is a DRW — does this kit fit?\u003c\/strong\u003e\u003cbr\u003eDRW models are in the BDS fitment data. DRW owners should verify inner wheel clearance to the upper U-bolt plate on 5.5–6 inch kits before ordering.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eDoes ADAS need to be recalibrated after installation?\u003c\/strong\u003e\u003cbr\u003eYes. All ADAS sensors require professional recalibration after installation. All recalibration costs are the owner's responsibility.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eManufacturer Data Disclaimer\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003eFitment, specification, included-component, and installation data for this kit are sourced from BDS Suspension manufacturer documentation and OFAS-verified product data current as of publication. Specifications are subject to change without notice; confirm current documentation for this SKU at the time of purchase.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eRequired Legal, Warning, Fitment, and Return Notices\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eExhaust Modification Warning:\u003c\/strong\u003e 6.4L gas models require exhaust modification to clear the front driveshaft before reinstallation. 5.7L gas models may require it. The vehicle can be driven without the front driveshaft to an exhaust shop.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eADAS Recalibration Warning:\u003c\/strong\u003e This kit alters vehicle ride height and suspension geometry. All advanced driver assistance system (ADAS) sensors require professional recalibration after installation. Schedule recalibration at an authorized dealer or certified ADAS service center. All recalibration costs are the owner's responsibility.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eInstallation Warning:\u003c\/strong\u003e Professional installation is strongly recommended. This kit is rated Difficult. Step drill bit, drill\/bit set, pitman arm puller, and welding equipment are required specialty tools. A professional wheel alignment is required after installation.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eTire Fitment Notice:\u003c\/strong\u003e BDS references configurations up to 37 x 13.50-inch tires. Trimming may be required. Buyer is responsible for verifying tire and wheel clearance for their specific vehicle and build.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eCalifornia Proposition 65 Warning:\u003c\/strong\u003e This product can expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to \u003ca href=\"http:\/\/www.P65Warnings.ca.gov\"\u003ewww.P65Warnings.ca.gov\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eReturn Policy:\u003c\/strong\u003e All returns require prior authorization from Obsidian Forged Auto Supply — do not ship any product back without a Return Merchandise Authorization (RMA). To request an RMA, contact OFAS at \u003ca href=\"mailto:Support@obsidianforgedautosupply.com\"\u003eSupport@obsidianforgedautosupply.com\u003c\/a\u003e or 469-407-7538 (Monday–Friday 9am–5pm CST, Saturday 9am–3pm CST) with your order number, product SKU, return reason, and photos. Return requests must be submitted within 90 days of delivery. To qualify, the product must be new, unused, uninstalled, complete with all hardware and included components, and in original manufacturer packaging. Do not write on, tape to, or place shipping labels directly on the manufacturer's product box. Return shipping is the customer's responsibility in all cases. Non-defective returns may be subject to a 15% restocking fee. No restocking fee applies when OFAS shipped the wrong item or the return is due to a verified defect or approved damage claim. Some products — including special-order, electrical, and installed items — may be non-returnable. Return eligibility is also subject to applicable manufacturer and supplier return requirements. Approved refunds are issued to the original payment method within approximately 10 business days of the warehouse receiving and processing the returned product. For damaged, missing, or incorrect shipments, contact OFAS within 48 hours of delivery, retain all packaging, and do not install the product.\u003c\/p\u003e","brand":"BDS Suspension","offers":[{"title":"Default Title","offer_id":51395820716353,"sku":"1619FS","price":3129.35,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0974\/1284\/1793\/files\/BDS1619FS.webp?v=1771168120","url":"https:\/\/obsidianforgedautosupply.com\/products\/bds-5-5-inch-lift-kit-bds1619fs-ram-3500-2013-2018-gas","provider":"Obsidian Forged Auto Supply","version":"1.0","type":"link"}