{"product_id":"bds-4-inch-lift-kit-bds1764fs-dodge-ram-2500-power-wagon-2006-2007","title":"BDS 4-Inch Lift Kit — Dodge Ram 2500 Power Wagon SKU: BDS1764FS | Dodge Ram 2500 Power Wagon 2006–2007 | Gas | 4\" Front \/ 4\" Rear | FOX 2.0 Performance Series | Leaf Springs Rear | 3-1\/2 Inch Axle","description":"\u003cp dir=\"ltr\"\u003eA complete 4-inch suspension lift kit engineered specifically for the 2006–2007 Dodge Ram 2500 Power Wagon gas. BDS-engineered lower control arms are longer than stock to rotate the axle for proper alignment, paired with a relocation mounting bracket to flatten the upper control arm angle. Gas-specific progressive rate Pro-Ride coil springs provide the 4-inch front lift. Forged drop pitman arm and track bar bracket correct steering geometry. The rear uses progressive rate multi-leaf springs for a 4-inch rear lift with extended U-bolts — configured for the 3-1\/2 inch axle. FOX 2.0 Performance Series shocks front and rear. Clears up to 36-inch tires.\u003c\/p\u003e\n\u003chr\u003e\n\u003cblockquote dir=\"ltr\"\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eBefore ordering:\u003c\/strong\u003e This kit is designed for the Dodge Ram 2500 Power Wagon only — it is not a general Ram 2500 kit. Gas engine only. \u003cstrong\u003eYou must measure your rear axle tube diameter before ordering — this kit is configured for the 3-1\/2 inch axle.\u003c\/strong\u003e Two rear axle diameters exist on this generation Ram. \u003cstrong\u003eIf your truck's steering gear box has been replaced and the sector shaft diameter measures approximately 1-1\/2 to 1-5\/8 inches, you must add BDS082404 to your kit.\u003c\/strong\u003e Exhaust modification may be required to clear the front driveshaft at full suspension droop — confirm with your installer before scheduling. Welding equipment and a cut-off wheel are required specialty tools.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003cblockquote dir=\"ltr\"\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eRequired separately (conditional):\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eBDS082404 — Required if steering gear box has been replaced and sector shaft diameter is approximately 1-1\/2 to 1-5\/8 inches\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch4 dir=\"ltr\"\u003eVerified Fitment\u003c\/h4\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eYear\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eMake\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eModel\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSubmodel\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eDrive\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eFuel\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eNotes\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2006\u003c\/td\u003e\n\u003ctd\u003eDodge\u003c\/td\u003e\n\u003ctd\u003eRam 2500\u003c\/td\u003e\n\u003ctd\u003ePower Wagon\u003c\/td\u003e\n\u003ctd\u003eAll drive types per BDS data\u003c\/td\u003e\n\u003ctd\u003eGas only\u003c\/td\u003e\n\u003ctd\u003eMeasure rear axle before ordering\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2007\u003c\/td\u003e\n\u003ctd\u003eDodge\u003c\/td\u003e\n\u003ctd\u003eRam 2500\u003c\/td\u003e\n\u003ctd\u003ePower Wagon\u003c\/td\u003e\n\u003ctd\u003eAll drive types per BDS data\u003c\/td\u003e\n\u003ctd\u003eGas only\u003c\/td\u003e\n\u003ctd\u003eMeasure rear axle before ordering\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003ePower Wagon only.\u003c\/strong\u003e This kit is not designed for standard Ram 2500 configurations.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eComponent Specifications\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eLift Configuration (this SKU):\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eAttribute\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eBDS Suspension\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSKU\u003c\/td\u003e\n\u003ctd\u003eBDS1764FS\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFront lift height\u003c\/td\u003e\n\u003ctd\u003e4 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFront lift method\u003c\/td\u003e\n\u003ctd\u003eCoil spring\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRear lift height\u003c\/td\u003e\n\u003ctd\u003e4 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRear lift method\u003c\/td\u003e\n\u003ctd\u003eLeaf spring\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRear axle configuration\u003c\/td\u003e\n\u003ctd\u003e3-1\/2 inch axle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShock option (this build)\u003c\/td\u003e\n\u003ctd\u003eFOX 2.0 Performance Series\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum tire clearance\u003c\/td\u003e\n\u003ctd\u003eUp to 36 inches (trimming may be required)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEstimated install time\u003c\/td\u003e\n\u003ctd\u003e8 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDifficulty level\u003c\/td\u003e\n\u003ctd\u003eModerate\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpecialty tools required\u003c\/td\u003e\n\u003ctd\u003eCut-off wheel or equivalent, grinder\/sanding disc, pitman arm puller, welding equipment\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003ePro-Ride Coil Springs — Front:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eAttribute\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eType\u003c\/td\u003e\n\u003ctd\u003eFull-length, progressive rate\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eApplication\u003c\/td\u003e\n\u003ctd\u003eGas-specific\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLift provided\u003c\/td\u003e\n\u003ctd\u003e4 inches (front)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eControl Arms:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eAttribute\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eLower control arms\u003c\/td\u003e\n\u003ctd\u003eBDS-engineered — longer than stock to rotate axle for proper alignment\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eUpper control arm bracket\u003c\/td\u003e\n\u003ctd\u003eRelocation mounting bracket to flatten upper control arm angle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAll four control arms\u003c\/td\u003e\n\u003ctd\u003eIncluded\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eRear Lift — Leaf Springs:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eAttribute\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eType\u003c\/td\u003e\n\u003ctd\u003eMulti-leaf, progressive rate\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLift provided\u003c\/td\u003e\n\u003ctd\u003e4 inches (rear)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAxle configuration\u003c\/td\u003e\n\u003ctd\u003e3-1\/2 inch axle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAxle wrap\u003c\/td\u003e\n\u003ctd\u003eReduced vs. block configuration\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePayload rating\u003c\/td\u003e\n\u003ctd\u003eFactory payload weight ratings maintained\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eFOX 2.0 Performance Series Shocks (front and rear):\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eAttribute\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBody diameter\u003c\/td\u003e\n\u003ctd\u003e2 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBody material\u003c\/td\u003e\n\u003ctd\u003eImpact extruded aluminum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDesign\u003c\/td\u003e\n\u003ctd\u003eInternal floating piston (IFP) monotube\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMounting ends\u003c\/td\u003e\n\u003ctd\u003eCNC machined 6061-T6 aluminum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShaft\u003c\/td\u003e\n\u003ctd\u003e5\/8-inch hard chrome plated heat-treated alloy steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePiston\u003c\/td\u003e\n\u003ctd\u003eRace-developed high-flow design\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eValving\u003c\/td\u003e\n\u003ctd\u003eApplication-specific\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFinish\u003c\/td\u003e\n\u003ctd\u003eClear anodized\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eRecommended Tire and Wheel Configuration (trimming may be required):\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eTire Size\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eWheel\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eBackspace\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e36 x 12.50\u003c\/td\u003e\n\u003ctd\u003e17 x 9\u003c\/td\u003e\n\u003ctd\u003e5 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003ch4 dir=\"ltr\"\u003eWhat Is and Is NOT Included\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eIncluded — Front:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eGas-specific progressive rate Pro-Ride coil springs (pair)\u003c\/li\u003e\n\u003cli\u003eBDS-engineered lower control arms (pair — longer than stock)\u003c\/li\u003e\n\u003cli\u003eUpper control arm relocation mounting brackets\u003c\/li\u003e\n\u003cli\u003eForged drop pitman arm\u003c\/li\u003e\n\u003cli\u003eTrack bar relocation bracket\u003c\/li\u003e\n\u003cli\u003eSway bar links\u003c\/li\u003e\n\u003cli\u003eBump stops\u003c\/li\u003e\n\u003cli\u003eFOX 2.0 Performance Series front shocks\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eIncluded — Rear:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eMulti-leaf progressive rate rear springs (4-inch, 3-1\/2 inch axle configuration)\u003c\/li\u003e\n\u003cli\u003eExtended U-bolts\u003c\/li\u003e\n\u003cli\u003eFOX 2.0 Performance Series rear shocks\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eNot included (conditional — may be required):\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eBDS082404 — Required if steering gear box has been replaced and sector shaft diameter is approximately 1-1\/2 to 1-5\/8 inches\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eCritical Compatibility\u003c\/h4\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower Wagon only:\u003c\/strong\u003e This kit is designed specifically for the Dodge Ram 2500 Power Wagon. It is not designed for standard Ram 2500 configurations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGas engine only:\u003c\/strong\u003e Gas-specific Pro-Ride coil springs are included. Diesel is not supported.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRear axle measurement required — 3-1\/2 inch axle configuration:\u003c\/strong\u003e Two rear axle diameters exist on this generation Ram. Measure your rear axle tube before ordering. The wrong axle selection results in an incompatible rear kit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSteering gear box sector shaft check:\u003c\/strong\u003e If the steering gear box has been replaced and the sector shaft diameter measures approximately 1-1\/2 to 1-5\/8 inches, BDS082404 must be added. Inspect before ordering.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExhaust modification — conditional:\u003c\/strong\u003e Exhaust modification may be required to clear the front driveshaft at full suspension droop. Confirm with your installer before scheduling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWelding equipment required:\u003c\/strong\u003e Cut-off wheel or equivalent, grinder\/sanding disc, and welding equipment are required specialty tools. Confirm installer capability before scheduling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eADAS recalibration:\u003c\/strong\u003e Required after installation. All recalibration costs are the owner's responsibility.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTire fitment:\u003c\/strong\u003e Clears up to 36 x 12.50-inch tires. Minor trimming may be required.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eInstallation Notes\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003eProfessional installation is strongly recommended. This kit is rated Moderate with an estimated installation time of 8 hours. Specialty tools required: cut-off wheel or equivalent, grinder\/sanding disc, pitman arm puller, and welding equipment.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eVerify before beginning:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eRear axle tube diameter confirmed as 3-1\/2 inch\u003c\/li\u003e\n\u003cli\u003eSteering gear box replacement and sector shaft check (if replaced, measure — if 1-1\/2 to 1-5\/8 inches, add BDS082404)\u003c\/li\u003e\n\u003cli\u003eConfirm with installer whether exhaust modification is needed for driveshaft clearance at full droop\u003c\/li\u003e\n\u003cli\u003eInstaller has welding equipment, cut-off wheel, and grinder\u003c\/li\u003e\n\u003cli\u003eADAS recalibration appointment scheduled\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003eProfessional alignment is required after installation. Refer to the current BDS Suspension installation instructions for SKU BDS1764FS for complete procedures, torque specifications, and component-specific instructions.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eThe Obsidian Take\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003eThe BDS1764FS is a Power Wagon-specific kit — built for the 2006–2007 Dodge Ram 2500 Power Wagon gas platform, not a general Ram 2500 fitment. The BDS-engineered longer lower control arms correct axle positioning and flatten the upper control arm angle at this lift height. Gas-specific Pro-Ride coil springs, leaf spring rear on the 3-1\/2 inch axle, and FOX 2.0 shocks complete the build. The pre-order checklist mirrors the adjacent generation Dodge kits: measure the rear axle tube diameter, check the steering gear box sector shaft if it has ever been replaced, and confirm welding equipment is on site. The exhaust modification requirement is conditional at full droop — ask the installer to evaluate clearance during the build rather than treating it as a definite pre-installation step.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eThis Product Is For You If\u003c\/h4\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eYou own a 2006 or 2007 Dodge Ram 2500 Power Wagon gas with a confirmed 3-1\/2 inch rear axle.\u003c\/li\u003e\n\u003cli\u003eYou want the leaf spring rear option for reduced axle wrap, improved stability, and maintained factory payload ratings.\u003c\/li\u003e\n\u003cli\u003eYou want 4 inches of front lift and 4 inches of rear lift with FOX 2.0 Performance Series shocks.\u003c\/li\u003e\n\u003cli\u003eYou want up to 36-inch tire clearance.\u003c\/li\u003e\n\u003cli\u003eYour truck's steering gear box is factory original, or if replaced, the sector shaft is not in the 1-1\/2 to 1-5\/8 inch range (or you will add BDS082404).\u003c\/li\u003e\n\u003cli\u003eYour installer has welding equipment, a cut-off wheel, and a grinder.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eThis Product Is Not For You If\u003c\/h4\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eYour truck is a standard Ram 2500 — this kit is Power Wagon-specific.\u003c\/li\u003e\n\u003cli\u003eYou have not measured your rear axle tube diameter.\u003c\/li\u003e\n\u003cli\u003eYour rear axle is 4 inches — see the 4-inch axle variant.\u003c\/li\u003e\n\u003cli\u003eYour truck's steering gear box has been replaced with a sector shaft diameter of approximately 1-1\/2 to 1-5\/8 inches and you have not added BDS082404.\u003c\/li\u003e\n\u003cli\u003eYour installer does not have welding equipment or a cut-off wheel.\u003c\/li\u003e\n\u003cli\u003eYou want the block rear option — see the block kit variant.\u003c\/li\u003e\n\u003cli\u003eYou want NX2 Nitro Series shocks — see the NX2 variant.\u003c\/li\u003e\n\u003cli\u003eYou want FOX 2.5 Performance Elite Series shocks — see the FOX 2.5 variant.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eProduct Family Reference\u003c\/h4\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eSKU\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eRear Option\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eAxle\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eShock\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eNotes\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBDS1764FS (this product)\u003c\/td\u003e\n\u003ctd\u003eLeaf Springs\u003c\/td\u003e\n\u003ctd\u003e3-1\/2 Inch\u003c\/td\u003e\n\u003ctd\u003eFOX 2.0\u003c\/td\u003e\n\u003ctd\u003ePower Wagon 2006–2007 Gas\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e4-inch axle variant\u003c\/td\u003e\n\u003ctd\u003eLeaf Springs\u003c\/td\u003e\n\u003ctd\u003e4 Inch\u003c\/td\u003e\n\u003ctd\u003eFOX 2.0\u003c\/td\u003e\n\u003ctd\u003eMeasure before ordering\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBlock kit variants\u003c\/td\u003e\n\u003ctd\u003eBlock\u003c\/td\u003e\n\u003ctd\u003e3-1\/2 or 4 Inch\u003c\/td\u003e\n\u003ctd\u003eVarious\u003c\/td\u003e\n\u003ctd\u003eMeasure before ordering\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNX2 variants\u003c\/td\u003e\n\u003ctd\u003eLeaf or Block\u003c\/td\u003e\n\u003ctd\u003eVarious\u003c\/td\u003e\n\u003ctd\u003eNX2 Nitro\u003c\/td\u003e\n\u003ctd\u003e—\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003ch4 dir=\"ltr\"\u003eCommon Questions\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eIs this kit compatible with standard Ram 2500 trucks?\u003c\/strong\u003e\u003cbr\u003eNo. This kit is engineered specifically for the Dodge Ram 2500 Power Wagon. It is not designed for standard Ram 2500 configurations.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhy do I need to measure my rear axle before ordering?\u003c\/strong\u003e\u003cbr\u003eTwo different rear axle tube diameters exist on this generation Ram. Ordering the wrong configuration produces an incompatible rear kit. Measure your axle tube before placing your order.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eIs exhaust modification required?\u003c\/strong\u003e\u003cbr\u003eBDS states that exhaust modification may be required to clear the front driveshaft at full suspension droop. This is a conditional requirement — confirm with your installer during the build process.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhat is the sector shaft check?\u003c\/strong\u003e\u003cbr\u003eIf the steering gear box has been replaced, the replacement unit may have a different sector shaft diameter. If it measures approximately 1-1\/2 to 1-5\/8 inches, BDS082404 is required. Inspect before ordering.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eDoes ADAS need to be recalibrated after installation?\u003c\/strong\u003e\u003cbr\u003eYes. All ADAS sensors require professional recalibration after installation. All recalibration costs are the owner's responsibility.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eManufacturer Data Disclaimer\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003eFitment, specification, included-component, and installation data for this kit are sourced from BDS Suspension manufacturer documentation and OFAS-verified product data current as of publication. Manufacturer specifications and included components are subject to change without notice; confirm current documentation for this SKU at the time of purchase.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eRequired Legal, Warning, Fitment, and Return Notices\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eFitment Notice:\u003c\/strong\u003e This kit is designed specifically for the Dodge Ram 2500 Power Wagon and will not fit standard Ram 2500 configurations. Gas engine only.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eRear Axle Warning:\u003c\/strong\u003e Two rear axle tube diameters exist on this generation Ram. Measure your rear axle tube before ordering. Ordering the wrong axle configuration produces an incompatible rear kit.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSteering Gear Box Warning:\u003c\/strong\u003e If the steering gear box has been replaced and the sector shaft diameter measures approximately 1-1\/2 to 1-5\/8 inches, BDS082404 must be added to this kit.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eADAS Recalibration Warning:\u003c\/strong\u003e This kit alters vehicle ride height and suspension geometry. All advanced driver assistance system (ADAS) sensors require professional recalibration after installation. Schedule recalibration at an authorized dealer or certified ADAS service center. All recalibration costs are the owner's responsibility.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eInstallation Warning:\u003c\/strong\u003e Professional installation is strongly recommended. Welding equipment, a cut-off wheel or equivalent, and a grinder\/sanding disc are required specialty tools. A professional wheel alignment is required after installation.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eTire Fitment Notice:\u003c\/strong\u003e Up to 36 x 12.50-inch tires are supported. Trimming may be required. Buyer is responsible for verifying tire and wheel clearance for their specific vehicle and build.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eCalifornia Proposition 65 Warning:\u003c\/strong\u003e This product can expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to \u003ca href=\"http:\/\/www.P65Warnings.ca.gov\"\u003ewww.P65Warnings.ca.gov\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eReturn Policy:\u003c\/strong\u003e All returns require prior authorization from Obsidian Forged Auto Supply — do not ship any product back without a Return Merchandise Authorization (RMA). To request an RMA, contact OFAS at \u003ca href=\"mailto:Support@obsidianforgedautosupply.com\"\u003eSupport@obsidianforgedautosupply.com\u003c\/a\u003e or 469-407-7538 (Monday–Friday 9am–5pm CST, Saturday 9am–3pm CST) with your order number, product SKU, return reason, and photos. Return requests must be submitted within 90 days of delivery. To qualify, the product must be new, unused, uninstalled, complete with all hardware and included components, and in original manufacturer packaging. Do not write on, tape to, or place shipping labels directly on the manufacturer's product box. Return shipping is the customer's responsibility in all cases. Non-defective returns may be subject to a 15% restocking fee. No restocking fee applies when OFAS shipped the wrong item or the return is due to a verified defect or approved damage claim. Some products — including special-order, electrical, and installed items — may be non-returnable. Return eligibility is also subject to applicable manufacturer and supplier return requirements. Approved refunds are issued to the original payment method within approximately 10 business days of the warehouse receiving and processing the returned product. For damaged, missing, or incorrect shipments, contact OFAS within 48 hours of delivery, retain all packaging, and do not install the product.\u003c\/p\u003e","brand":"BDS Suspension","offers":[{"title":"Default Title","offer_id":51395820945729,"sku":"1764FS","price":3061.96,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0974\/1284\/1793\/files\/BDS1764FS.jpg?v=1771167114","url":"https:\/\/obsidianforgedautosupply.com\/products\/bds-4-inch-lift-kit-bds1764fs-dodge-ram-2500-power-wagon-2006-2007","provider":"Obsidian Forged Auto Supply","version":"1.0","type":"link"}