{"product_id":"apex-prolock-tie-rod-drag-link-kit125-polished-jeep-jl-jt-dana30-44-narrow-flip","title":"Apex ProLock Tie Rod \u0026 Drag Link Assembly — SKU: KIT125 — Polished Aluminum | Dana 30\/44 Narrow Axle | Flip Kit (Over-Knuckle) | Jeep Wrangler JL 2018–2026 \/ Gladiator JT 2019–2026 4WD","description":"\u003cdiv class=\"standard-markdown grid-cols-1 grid [\u0026amp;_\u0026gt;_*]:min-w-0 gap-3\"\u003e\n\u003ch4 dir=\"ltr\"\u003eOverview\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003eThis is a complete replacement tie rod and drag link kit for the Jeep Wrangler JL and Gladiator JT — a highly polished 2\" 7075-T6 aluminum tie rod and drag link, each using forged steel tie rod and drag link ends with an E-coat finish, Apex's ProLock keyway washer system, and zerk-fitting serviceability. This exact configuration is built for the Dana 30 \/ narrow Dana 44 front axle and is set up as a Flip Kit (over-knuckle mount), including the required taper sleeve.\u003c\/p\u003e\n\u003chr\u003e\n\u003cblockquote\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eBefore ordering:\u003c\/strong\u003e This kit fits the Dana 30 or narrow Dana 44 front axle only — typically found on non-Rubicon trims (Sport, Sahara). Wide Dana 44 axles (typically Rubicon, Mohave, Max Tow Package) require a different, wide-axle version of this kit — not this SKU. To confirm your axle width, measure ball-stud center to ball-stud center on your factory tie rod: narrow Dana 44 measures 57½\"–58½\"; wide Dana 44 measures 60½\"–61½\". This configuration is the Flip Kit (over-knuckle mount) and requires drilling the knuckle drag link mount through with a straight 7\/8\" drill bit to install the included taper sleeve — this is typically suggested for lifts over 4.5\". If your Jeep has been upgraded to a Dana 60 axle, contact Apex directly for available modifications; this kit as configured does not cover that application.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003cblockquote\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eRequired separately:\u003c\/strong\u003e A steering stabilizer bracket is not included and must be selected separately based on the steering stabilizer you run. Apex jam nut wrenches KIT521 (2x WR112 41mm\/46mm) are required for installation and are not included with this listing. A steering stabilizer, thread locker (blue Loctite 243 or Permatex 24206), anti-seize for adjusting-sleeve threads only, and a professional alignment are also required and not included.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch4 dir=\"ltr\"\u003eVerified Fitment\u003c\/h4\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eMake\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eModel\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eModel Years\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eDrivetrain\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eAxle Requirement\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eJeep\u003c\/td\u003e\n\u003ctd\u003eWrangler JL\u003c\/td\u003e\n\u003ctd\u003e2018–2026\u003c\/td\u003e\n\u003ctd\u003e4WD\u003c\/td\u003e\n\u003ctd\u003eDana 30 or narrow Dana 44 front axle only (typically non-Rubicon: Sport, Sahara)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eJeep\u003c\/td\u003e\n\u003ctd\u003eGladiator JT\u003c\/td\u003e\n\u003ctd\u003e2019–2026\u003c\/td\u003e\n\u003ctd\u003e4WD\u003c\/td\u003e\n\u003ctd\u003eDana 30 or narrow Dana 44 front axle only (typically non-Rubicon: Sport, Sahara)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp dir=\"ltr\"\u003e\u003cem\u003eWide Dana 44 axle trucks (typically Rubicon, Mohave, Max Tow Package) require the wide-axle version of this kit — not this SKU. Dana 60 upgrades require contacting Apex directly.\u003c\/em\u003e\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eComponent Specifications\u003c\/h4\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eAttribute\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eApex Chassis\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSKU\u003c\/td\u003e\n\u003ctd\u003eKIT125 — Polished Aluminum, Dana 30\/44 Narrow, Flip Kit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eKit type\u003c\/td\u003e\n\u003ctd\u003eComplete tie rod and drag link replacement assembly\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVehicle position\u003c\/td\u003e\n\u003ctd\u003eFront\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eQuantity per vehicle\u003c\/td\u003e\n\u003ctd\u003e1 kit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAdjusting rod (tie rod and drag link)\u003c\/td\u003e\n\u003ctd\u003e2\" 7075-T6 Aluminum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAdjusting sleeve finish\u003c\/td\u003e\n\u003ctd\u003eClear polished — highly polished aluminum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTie rod and drag link end finish\u003c\/td\u003e\n\u003ctd\u003eE-coating (electrochemical finish)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHousing material\u003c\/td\u003e\n\u003ctd\u003eSAE 1045 Solid Steel, forged, CNC machined\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBall stud material\u003c\/td\u003e\n\u003ctd\u003eSAE 4140 Chromoly, hot forged, induction heat treated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBall stud threads\u003c\/td\u003e\n\u003ctd\u003eRolled and step-threaded\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBearing type\u003c\/td\u003e\n\u003ctd\u003eMetal-to-metal; \"Flopper Stopper\" design built into tie rod ends and the right-hand drag link end, rated for 27° of stud swing left and right\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBoot material\u003c\/td\u003e\n\u003ctd\u003eCR rubber, accordion style\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHardware\u003c\/td\u003e\n\u003ctd\u003eGrade 8 \/ Class 10.9; castle nut\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLocking system\u003c\/td\u003e\n\u003ctd\u003eProLock keyway washer (patent-pending); Belleville washer available as an alternative on select joints — use one or the other, never both on the same joint\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTie rod part numbers\u003c\/td\u003e\n\u003ctd\u003eTR181K, TR182K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDrag link part numbers\u003c\/td\u003e\n\u003ctd\u003eDL112KF (knuckle side, Flip configuration), DL111K (pitman arm side)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTaper sleeve\u003c\/td\u003e\n\u003ctd\u003eIncluded with this Flip Kit configuration; requires a straight 7\/8\" drilled hole through the knuckle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eZerk fittings\u003c\/td\u003e\n\u003ctd\u003eIncluded, pre-threaded; kit pre-greased\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAdjusting sleeves\u003c\/td\u003e\n\u003ctd\u003eMade in the USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWarranty\u003c\/td\u003e\n\u003ctd\u003eApex Honor System — lifetime of vehicle (original purchaser, registration required)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003ch4 dir=\"ltr\"\u003eWhat Is and Is NOT Included\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eIncluded:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eComplete tie rod assembly — 2\" 7075-T6 polished aluminum adjusting sleeve, forged steel E-coated ends (TR181K, TR182K)\u003c\/li\u003e\n\u003cli\u003eComplete drag link assembly — 2\" 7075-T6 polished aluminum adjusting sleeve, forged steel E-coated ends (DL112KF, DL111K)\u003c\/li\u003e\n\u003cli\u003eTaper sleeve (Flip Kit configuration)\u003c\/li\u003e\n\u003cli\u003eProLock keyway washers and Belleville washer alternates\u003c\/li\u003e\n\u003cli\u003eJam nuts with integrated set screws\u003c\/li\u003e\n\u003cli\u003eGrade 8 \/ Class 10.9 hardware, castle nuts\u003c\/li\u003e\n\u003cli\u003eZerk fittings (pre-threaded, pre-greased)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eNot included:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eSteering stabilizer bracket (must be selected separately based on the steering stabilizer used)\u003c\/li\u003e\n\u003cli\u003eSteering stabilizer\u003c\/li\u003e\n\u003cli\u003eJam nut wrenches (KIT521, 2x WR112 41mm\/46mm — required for installation, sold separately)\u003c\/li\u003e\n\u003cli\u003eReplacement set screws (XP172, tie rod and drag link, sold separately)\u003c\/li\u003e\n\u003cli\u003eThread locker (blue Loctite 243 or blue Permatex 24206 recommended)\u003c\/li\u003e\n\u003cli\u003eAnti-seize compound (for adjusting sleeve threads only)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eCritical Compatibility\u003c\/h4\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003e\n\u003cstrong\u003eAxle width:\u003c\/strong\u003e This configuration fits the Dana 30 or narrow Dana 44 front axle only. Confirm by measuring ball-stud center to ball-stud center on your factory tie rod: 57½\"–58½\" indicates narrow Dana 44 (correct for this kit); 60½\"–61½\" indicates wide Dana 44, which requires a different kit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDana 60 upgrades:\u003c\/strong\u003e Not covered by this configuration. Contact Apex directly for available modifications.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlip Kit (over-knuckle mount):\u003c\/strong\u003e Requires drilling the knuckle drag link mount through with a straight 7\/8\" drill bit to install the included taper sleeve. Typically suggested for lifts over 4.5\".\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWasher selection:\u003c\/strong\u003e Use either the ProLock keyway washer or the Belleville washer to secure a given jam nut — never both on the same joint.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAnti-flop bearing (tie rod):\u003c\/strong\u003e Allows approximately 4° of forward\/back rotation once properly installed. Tighten the passenger side jam nut first, then center the flop while tightening the driver's side jam nut, so approximately 4° of rotation remains once both are torqued.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMinimum engagement mark — drag link:\u003c\/strong\u003e If visible on the drag link end threads, thread engagement is insufficient. A flip kit or re-equalized adjusting sleeve may be required.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrease volume:\u003c\/strong\u003e Zerk fittings are metal-on-metal and pre-greased. Add only ½ to 1 pump of high-pressure lithium grease per fitting — over-greasing can cause the boots to balloon and fail.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePolished finish care:\u003c\/strong\u003e Polished raw aluminum is uncoated and will oxidize\/dull with exposure unless periodically maintained; this is a cosmetic characteristic of the finish, not a defect.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSteering stabilizer bracket:\u003c\/strong\u003e Not included with this kit — select the correct bracket separately based on your steering stabilizer.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eInstallation Notes\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003eSteering components are safety-critical. Professional installation is strongly recommended, and a professional alignment must be completed before operating the vehicle. The installer must follow the current Apex Chassis Flip Kit installation instructions supplied with the product throughout installation and alignment, including drilling the knuckle for the taper sleeve.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eRequired for this configuration:\u003c\/strong\u003e Apex jam nut wrenches KIT521 (2x WR112 41mm\/46mm), sold separately; medium-strength blue thread locker (Loctite 243 or Permatex 24206); anti-seize compound for the internal adjusting-sleeve threads only; and a straight 7\/8\" drill bit for the knuckle taper-sleeve hole.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003eTie rod ball-stud tension nuts torque to 63–67 ft\/lbs; drag link castle nuts torque to 75–82 ft\/lbs; jam nuts on both assemblies torque to 200 ft\/lbs; jam-nut set screws torque to 8–10 ft\/lbs, applied only after alignment. The tie rod's ProLock keyway washers are tapped onto the adjusting sleeve after alignment. Before operating the vehicle, verify correct application, steering geometry, adequate thread engagement, and full lock-to-lock clearance.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003eInspect jam-nut position after the initial 500 miles and then every 5,000 miles or at each oil change, consistent with Apex's maintenance guidance. Refer to the current Apex Chassis installation instructions supplied with this kit for complete procedures, torque specifications, and all safety requirements.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eThe Obsidian Take\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003eThis KIT125 configuration is Apex's polished aluminum tie rod and drag link kit for the Jeep Wrangler JL and Gladiator JT running the Dana 30 or narrow Dana 44 front axle — set up as a Flip Kit for lifted applications, with the taper sleeve included. Confirm these application conditions before ordering: this kit is axle-width specific, so measure your factory tie rod before ordering if you're unsure whether your Dana 44 is narrow or wide, and the Flip configuration requires drilling the knuckle for the taper sleeve. Jam nut wrenches (KIT521) and a steering stabilizer bracket are not included and must be ordered separately.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eThis Product Is For You If\u003c\/h4\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eYou own a 2018–2026 Jeep Wrangler JL or 2019–2026 Gladiator JT with a Dana 30 or narrow Dana 44 front axle (typically Sport or Sahara trim).\u003c\/li\u003e\n\u003cli\u003eYou are running a lift over 4.5\" and want an over-knuckle (Flip) mount with the taper sleeve included.\u003c\/li\u003e\n\u003cli\u003eYou prefer a polished aluminum appearance.\u003c\/li\u003e\n\u003cli\u003eYou are prepared to drill the knuckle with a straight 7\/8\" bit as part of installation.\u003c\/li\u003e\n\u003cli\u003eYou are prepared for a professional-level installation with specific torque values and a required professional alignment.\u003c\/li\u003e\n\u003cli\u003eYou are prepared to select and purchase jam nut wrenches (KIT521) and a steering stabilizer bracket separately.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eThis Product Is Not For You If\u003c\/h4\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eYour Jeep has a wide Dana 44 front axle (typically Rubicon, Mohave, or Max Tow Package trim) — you need the wide-axle version of this kit, not this SKU.\u003c\/li\u003e\n\u003cli\u003eYour Jeep has been upgraded to a Dana 60 axle and you have not contacted Apex to confirm available modifications.\u003c\/li\u003e\n\u003cli\u003eYou need a standard under-knuckle mount rather than the Flip (over-knuckle) configuration.\u003c\/li\u003e\n\u003cli\u003eYou are not prepared to drill the knuckle for the taper sleeve.\u003c\/li\u003e\n\u003cli\u003eYou prefer a black finish — see KIT120 (black anodized aluminum).\u003c\/li\u003e\n\u003cli\u003eYou do not already have, or are not ordering, jam nut wrenches (KIT521) and a steering stabilizer bracket matched to your stabilizer.\u003c\/li\u003e\n\u003cli\u003eYou plan to use both ProLock and Belleville washers on the same joint — use one or the other only.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4 dir=\"ltr\"\u003eProduct Family Reference\u003c\/h4\u003e\n\u003cdiv dir=\"ltr\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth scope=\"col\"\u003eSKU\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eFinish\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eAxle\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eMount\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eKIT120\u003c\/td\u003e\n\u003ctd\u003eBlack anodized aluminum\u003c\/td\u003e\n\u003ctd\u003eDana 30\/44 narrow or Dana 44 wide (select)\u003c\/td\u003e\n\u003ctd\u003eStandard or Flip (select)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eKIT125 (this product)\u003c\/td\u003e\n\u003ctd\u003ePolished aluminum\u003c\/td\u003e\n\u003ctd\u003eDana 30\/44 narrow\u003c\/td\u003e\n\u003ctd\u003eFlip Kit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003ch4 dir=\"ltr\"\u003eCommon Questions\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eHow do I know if I have a narrow or wide Dana 44?\u003c\/strong\u003e\u003cbr\u003eMeasure your factory tie rod ball-stud center to ball-stud center. 57½\"–58½\" is narrow Dana 44 (this kit applies). 60½\"–61½\" is wide Dana 44 (a different kit is required).\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eDoes this fit the Rubicon?\u003c\/strong\u003e\u003cbr\u003eRubicon trucks typically run the wide Dana 44 axle, which requires the wide-axle version of this kit, not this narrow-axle SKU. Confirm your axle width by measurement if unsure.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhat's the difference between the standard and Flip Kit mount?\u003c\/strong\u003e\u003cbr\u003eThe standard mount is under-knuckle. The Flip Kit is an over-knuckle mount, includes the taper sleeve, and requires drilling the knuckle through with a straight 7\/8\" bit. It's typically used for lifts over 4.5\".\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eIs a steering stabilizer bracket included?\u003c\/strong\u003e\u003cbr\u003eNo. It must be selected separately based on the steering stabilizer you use.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eAre jam nut wrenches included?\u003c\/strong\u003e\u003cbr\u003eNo. Apex jam nut wrenches KIT521 (2x WR112 41mm\/46mm) are required and sold separately.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eCan I use Belleville washers instead of the ProLock keyway washers?\u003c\/strong\u003e\u003cbr\u003eYes, on the applicable joints — but never use both a ProLock and a Belleville washer on the same joint.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eDoes the polished finish need maintenance?\u003c\/strong\u003e\u003cbr\u003eThe polished aluminum is a raw, uncoated finish and may oxidize or dull with exposure over time. If you prefer a coated finish, see KIT120 (black anodized).\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eIs a professional alignment required?\u003c\/strong\u003e\u003cbr\u003eA professional alignment must be completed before operating the vehicle. Professional installation is strongly recommended. Thread locker and set-screw torque are applied only after alignment.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhat is the replacement set screw part number?\u003c\/strong\u003e\u003cbr\u003eXP172, for both the tie rod and drag link.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhat is the warranty?\u003c\/strong\u003e\u003cbr\u003eApex covers manufacturer defects, premature wear, and breakage for the life of the vehicle, as long as the original purchaser owns the vehicle, with product registration required within 90 days of purchase. See full warranty summary below.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eManufacturer Data Disclaimer\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003eFitment, specification, compatibility, installation, and warranty data for this kit are sourced from Apex Chassis manufacturer product documentation and installation instructions, and OFAS-verified product data current as of publication. Specifications are subject to change without notice; confirm current documentation for this SKU and configuration at the time of purchase.\u003c\/p\u003e\n\u003ch4 dir=\"ltr\"\u003eRequired Legal, Warning, Fitment, and Return Notices\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSafety Warning:\u003c\/strong\u003e Steering is a critical safety component. The installer must read and follow the provided installation instructions in full. Failure to follow these instructions may result in loss of vehicle control, accident, and injury. Failure to follow installation instructions and use correct installation tools may also void the warranty.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWarranty Summary:\u003c\/strong\u003e Apex Chassis warrants this product against manufacturer defects, premature wear, and breakage for the life of the vehicle, provided the original purchaser continues to own the vehicle. The product must be purchased through Apex Chassis directly or through an authorized Apex dealer, and must be registered with proof of purchase within 90 days of purchase. Products not registered within 90 days are covered only for 90 days from the date of purchase. Apex will, at its sole discretion, replace the defective part and cover ground shipping, or refund the original purchase price. Labor for removal or reinstallation is not covered. This warranty does not cover cosmetic imperfections, boots, bushings, or Heim-style joints, which are considered regular wear items. The warranty is void if the component is improperly installed, modified, or used in an application for which it was not designed, as determined at Apex's sole discretion. This warranty is governed by the laws of the State of Arizona.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Apex Chassis","offers":[{"title":"Default Title","offer_id":51408206659905,"sku":"KIT125-Dana30-YesFlip","price":1115.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0974\/1284\/1793\/files\/KIT125-Dana30-YesFlip-JJSP.webp?v=1771682527","url":"https:\/\/obsidianforgedautosupply.com\/products\/apex-prolock-tie-rod-drag-link-kit125-polished-jeep-jl-jt-dana30-44-narrow-flip","provider":"Obsidian Forged Auto Supply","version":"1.0","type":"link"}